（102）存储器指标取得错误 （103）装置初始化错误
（104）主轴停止位误差大于允许范围 （105）传感器号码的范围不在1到8 的范围内。
（106）热变位参数4的数值为0 （时间测量常数）
（107）热变位参数5的数值为0 （时间测量常数）
（108）热变位参数6的数值为0 （时间测量常数）
EX1991 SERVO ALARM(TLB) A34.1 Alarm of servo motor(TLB) refer to Refer to separate sheet (servo Alarm list .)
TLB: In- magazine Tool Breakage Detection.
EX1991 伺服报警 （刀具破损检测装置） 刀具破损检测装置的伺服马达报警请
参考伺服马达报警清单
EX2028 PRESS SINGLE BLOCK SWITCH A7.6 A cycle start has been activated at single Block off status.
EX2028 按下单步按键 执行程序需要将单步按键按下 EX2029 CYCLE START PERMISSION A7.7 Single block has been turned off or INPERFECT front door has been opened during Automatic cycle.
EX2029 循环启动条件不具备 在自动运行期间前门被打开了或者单 步按键被关掉了。
EX2200 TOOL PARAMETER ERROR A50.0 Alarm occurs in the library C. EX2200 刀具参数错误 计数器C里的值错误 EX2201 WAITING POT TOOL DATA
NOT FOUND A50.1 Tool data of waiting pot does not Exits in the tool file.
EX2201 没有等待刀号 刀具文件里没有等待刀号
EX2202 T-CODE TOOL GROUP NOT Group of T-code command tools does FOUND A50.2 not exist in the tool file.
EX2202 没发现刀具组里的刀号 刀具组里的刀号没有存在刀具文件里。 EX2203 TOOL DATA FOR SPINDLE A50.3 Data of spindle tool does not exist in the NOT FOUND tool file.
EX2203 没发现主轴刀号 刀具文件里不存在主轴刀号
EX2204 NO SPINDLE TOOL FOR T0 A50.4 No spindle tool exists when specifying T0 command.
EX2204 主轴上没有T0 刀具 指定的T0 刀号不在主轴上
EX2205 TOOL IN SETUP POS. NO . A50.5 Same tool No. as in the tool set position ERROR exsits in the tool file.
EX2205 刀号设置错误 在刀具文件里又指定了同样的刀号。
EX2206 SET POSITION TOOL DATA ERR A50.6 Data of tool set position exsits in the Tool file .
EX2206 刀具数据设置的位置错误 要设置的数据已存在刀具文件里了 EX2207 SET POSITION TOOL DIAMETER A50.7 Tool diameter of T data does not match ERROR the one of tool set position.
EX2207 刀具直径设置的位置错误 刀具数据里的刀具直径与刀具设置的 位置不匹配
EX2208 TOOL ID COMMUNICATION A51.0 Communication error occurs during ERROR (*) reading or writing of tool id data. EX2208 刀具ID 通讯错误 The numbers in the parentheses of The ID data communication error Correspond to the following alarms.
(1)Framing error between CNC and ID (2)Parity error in one character between CNC and ID controller
(3)Communication format error between
CNC and ID controller.
(4)Sum check error between CNC and ID and controller.
(5)CNC assigns the write to the protect Area.
(6)Mismatch error of ID chip.
(7)Hardware error of ID controller (8)Write error between ID controller And chip
(9)Write error between ID controller And chip. (verify error)
(10)Communication time over error Between CNC and ID controller. 读或写刀具ID数据时发生了通讯错误 参照括号里的ID数据号码通讯错误察看 下列报警。
（1）CNC和ID控制组帧错误
（2）CNC和ID控制在一个字符里发生了同位 错误
（3）CNC和ID控制中发生了通讯格式错误 （4）CNC和ID控制中发生了总数检测错误 （5）CNC指定写入到保护区 （6）ID芯片不匹配错误 （7）ID控制器的硬盘错误
（8）ID控制器和芯片之间写入错误
（9）ID控制器和芯片之间写入错误（校验错 误）。
（10）ID控制器和CNC之间通讯超时。
EX2209 TOOL DATA OF 8 FIGURES The tool number is not proper. Among all INCORRECT A51.1 eight bits, the numbers are not respectively Assigned in the upper and lower four digits. EX2209 8位数的刀具号不正确 刀具号是不正确的。在八数位中这个刀号 不能个别的从上或下分配给四位数里。 EX2210 TOOL DATA MM/INCH A51.2 MM or INCH tool file not match one of the SETTING ERROR NC side.
EX2210 刀具数据公英制设置错误 刀具文件的公制或英制在一个NC单元 里不匹配。
EX2212 TOOL ID DATA INCORRECT A51.4 When reading the tool ID data, incorrect Character has been entered.
EX2212 刀具ID号不正确 当读取刀具ID号时，输入了不正确的字符 EX2213 DNC1 DATA INCORRECT A51.5 When receiving DNC1 data, incorrect Character has been entered. EX2213 DNC1 数据不正确 当接受DNC1数据时，输入了不正确的字符 EX2214 TOOL OFFSET AMOUNT TOO A51.6 Offset amount of spindle tool is too large LARGE check the offset data.
EX2214 刀具偏置数量太大 主轴刀具偏置数太大，检察偏置数。 EX2215 DATA TABLE ABNORMAL A51.7 DNC1 data table is abnormally set .
EX2215 工作台数据异常 DNC1 里的工作台数据进行了异常设置 EX2216 TOOL GROUP DATA ERROR A52.0 When the tool skip (M66) command is Given the assigned group is not provided. EX2216 刀具组数据错误 刀具跳略命令发出但是分配组没有提供 EX2217 CRT IS CHANGED AUTO A52.1 The display is changed during auto tool ID MODE ID mode.
EX2217 CRT在自动模式下改变 在自动刀具ID模式下显示改变
EX2218 ID HEAD APPROACH TIME A52.2 Tool ID head approach has not completed OVER within specified time.
EX2218索引刀具起始位置 超时 索引刀具起始位置在指定时间没有完成 EX2219 ID HEAD RETRACTION TIME A52.3 Tool ID head retraction has not completed OVER within specified time.
EX2219刀具返回起始位置 超时 刀具返回起始位置在指定时间没有完成 EX2220 ID POT DATA ABNORMAL A52.4 Magazine offset number is abnormally set EX2220 刀杯号异常 刀库里的刀杯号码设置是异常的 EX2221 M67 COMMANDED ERROR A52.5 Alarm occurs during M67 command.
The numbers in the parentheses correspond To the following alarms. (-1) System error. (macro) (-2) System error. (offset window) (-3) System error.
(pot no. not found) (-4) System error.
(parameter error)
(10)illegal value at #1133. (11)illegal T-code command. (12)illegal use time set. (13)illegal skip flag set. (14)spindle tool nothing (15)tool not found.
(16)using tool not found (17)illegal H,D code set. EX2221 M67 命令错误 EX2222 ID CYCLE TIME OVER A52.6 EX2222 ID 循环时间超时 EX2228 SKIP TOOL IS CALLED A53.4 EX2228 刀具呼叫被跳过 EX2231 ID NO. ＆ FILE NO. NOT A53.7 Tool No. of ID does not match the MATCHED tool No. which is read out from the Tool file. EX2231 ID号与文件号不匹配 EX2232 DNC1 COMMUNICATION ERROR A54.0 Alarm The numbers in the parentheses of the DNC1 communication error munication Error correspond to the following
(18)spindle tool specified. (19)offset limit over.
(20)mm/inch setting error.
报警发生在执行M67命令中参照下列括号中 的报警
(-1)系统错误（宏）
(-2)系统错误（偏置窗口） (-3)系统错误（刀杯号没发现） (-4)系统错误（参数错误） (10)#1133的值无效 (11)无效的T代码指令 (12)所用的时间设置无效 (13)跳过标记设置无效 (14)没有主轴刀具 (15)没发现刀具
(16)说用的刀具没有发现 (17) H，D代码设置无效 (18) 主轴刀具被指定 (19)超过极限偏置
(20)公制/英制设置错误
Tool ID cycle has not completed within Specified time .
刀具ID循环在指定时间没有完成 Skip signal of specified T code tool is Turned on .
指定的刀号跳跃信号被打开
从刀具文件里读出的刀号与实际刀号的ID 不匹配
occurs during DNC1 communication